The Rycote Tac!T (pronounced "Tas-It") filter is an in-line, active "third-order" (18dB/octave) filter with a "knee" at approximately 60Hz. This enables it to pass, unaffected, virtually all of the desired audio, while massively reducing wind and handling noise, and floor transmitted vibrations. The energy in these extreme low frequency and infrasonic sounds can be very high, and if not attenuated, would otherwise cause overloads and disturbances across the entire audio spectrum.
The Tac!T filter draws its power from the P48 phantom supply while also passing power on to the microphone. It is electronically symmetrical and does not disturb the intrinsic balance of the microphone circuit, nor does it introduce any signal loss for normal programme frequencies.
|
 |
The flexible universal joint can be used on practically any microphone stand and gives you more freedom than ever by providing maximum flexibility for positioning a range of equipment such as microphones, hand-held recorders, etc. Included are a 3/8" male thread and 1/4" or 3/8" female thread. The integrated thread adapter allows for even more combinations.
|
|
The Rycote Wireless Receiver Camera Bracket is a universal wireless microphone receiver holder used to mount receivers onto a 1/4" mount or flash shoe on any camera. The MkII bracket features a brass thumbwheel which makes secure mounting easier as well as larger overall dimensions to improve compatibility with receivers. As with the Mk I it has 4 soft grip pads and hook-&-loop straps for securing receivers in place. A shoe mount is included.
|
|
From the Rycote stable - a foam wind gag for shotgun mics.
Suitable for the following microphones:- Sennheiser MKH 60 Sony ECM 672 |
|
From the Rycote stable - a foam wind gag for shotgun mics.
Suitable for the following microphones:- AKG C 568 EB, CK 68 ULS C460B Red Azden SG(M)-1X BeyerDynamic MCE 87vs, MC 836, MC 716, MC 726, MCE 86 N (C) S, MC 736 ClockAudio C850EDPA 4017 JVC DY-70U Røde NTG-3 Sanken CS 3 Sennheiser MKH 416, MKH 418, ME 66 K6, ME 80 K3USony ECM 680S, ECM 670, ECM 678 |
|
From the Rycote stable - a foam wind gag for camera mics.
Suitable for the following microphones:- SONY BVP5/BVP, BVP537, BVW |
|
A 70mm ( or 2 3/4" in your old money) wide table stand from Rycote.
It has a non-slip rubber base, and a 3/8" thread.
Can be used with a microphone or a portable recorder.
Rycote suggest you don't use this with mics longer than 250mm.
|
|
 The InVision® INV-7HG MKIII Stereo Pair Kit is a vibration-resistant, low-noise suspension system designed to mount paired microphones for stereo recording.
The Kit comprises two of Rycote's patented vibration-reducing Lyre® suspensions mounted on a rigid, slotted stereo bar. The dual InVision INV-7 HG MkIII Lyre® webs used in the Stereo Pair Kit can accommodate larger shotgun mics from 19 to 25mm in diameter, and up to 300mm long. The spacing between the two webs, and thus between the two mounted microphones, is quickly and simply adjustable from 40 to 200mm on the slotted bar by loosening a brass wheel under each Lyre and moving it laterally as required. A star-shaped knob underneath each Lyre® also allows each mic to be rotated and/or inclined, and then secured once optimal stereo imaging has been achieved.
The complete kit may be fitted to mic stands with 3/8-inch or 5/8-inch threads (adaptors for both types are included)
|
|
The Hot Shoe Extension allows you to fit multiple attachments such as lights and additional mics to your single hot shoe on your camera/camcorder. Because the Hot shoe Extension can rotate 360° around the shoe fixture on the camera, your microphone can be easily moved out of shot and also adjusted to achieve the optimum balance. This essential, yet affordable accessory is a must for all videographers.
|
|
A new and improved version of the stereo Back-to-Back clips are available now! The new clips are capable of holding 19-25mm diameter mics, and slab-sided MKH microphones in M/S stereo as before - but now have a soft grip surface on the internal edges to prevent microphones from slipping or rotating inside the clips.
SOLD IN PAIRS
|
|
Lyre®, 82 shore - with Grey rigid part (Heavy Grade) & Black Soft-grip, suitable for microphones of 19/25 mm diameter.
|
|
Lyre®, 82 shore - with Black rigid part & Grey Soft-grip, suitable for microphones of 19/25 mm diameter used on older pre-modular Rycote Suspensions with hoops fitted to the end of the bar.
|
|
The Rycote connbox is designed to reduce cable borne handling noise. The box mounts on the suspension bar and flying leads go to the microphone and pistol grip. This CB1 model is the new hard-wired version and is for use with mono microphones with a 3 pin XLR.
Bigger Picture...
|
|
For use with longer shotgun microphones (eg MKH816) with a 3 pin XLR. |
|
For use with most stereo rigs with a pair of 3 pin XLR's 2 x XLR3F / XLR5M This is the new hard-wired version. |
|
For use with single shank stereo microphones with a 5 pin XLR XLR5F / XLR5M This is the new hard-wired version. |
|
For use with a single Schoeps CCM microphone with a Lemo connector in a mono extended ball gag.
|
|
For use with an MS pair of Schoeps CCM microphones (Lemo connectors) in a mono extended ball gag. |
|
For use with an MS or XY pair of Schoeps CCM microphones (Lemo connectors) in a stereo extended ball gag. |
|
For Schopes CMIT-5U + CCM MS with XLR and Lemo Tail |
|
The newer stronger Pistol Grip from Rycote
|
|
Rycote's Extension Handle has been designed to allow products with a female 3/8" thread, i.e. portable audio recorder or camera to be either hand-held or mounted on a 3/8" male thread, such as a microphone stand or boom pole.
Thanks to its ergonomic, soft-grip feel, the handle can be used to comfortably hand-hold recording devices, and can be used together with our Portable Recorder Suspension, or InVision Broadcast suspension mounts.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Please specify when ordering for which model basket the filler strip is for. Thank you
|
|
